Bissell Vacuum Cleaner 79T3 User Manual

ReadyDry  
U S E R ’ S G U I D E  
79T3 SERIES 220-240v  
3
4
5
Safety Instructions  
Product view  
Assembly  
6
Special Features  
Operation  
7-10  
Maintenance and Care  
10-11  
Troubleshooting  
12  
13  
Consumer Services  
14 Replacement Parts  
14 Formulas  
15 Additional Accessories  
16 Warranty  
 
IMPORTANT SAFETY INSTRUCTIONS  
When using an electrical appliance, basic  
precautions should be observed, including  
the following:  
Not intended for use by persons (including  
children) with reduced sensory or mental capabilities,  
or lack of experience and knowledge, unless they  
have been given supervision or instruction concerning  
use of the appliance by a person responsible for  
their safety  
Young children should be supervised to ensure  
that they do not play with the appliance  
Do not pick up toxic material (chlorine bleach,  
ammonia, drain cleaner, petrol, etc.)  
Do not modify the Earthed plug  
Do not use for any purpose other than described  
in this User’s Guide  
Use only manufacturer’s recommended  
attachments  
Use only cleaning products formulated by  
BISSELL for use in this appliance to prevent  
internal component damage  
READ ALL INSTRUCTIONS  
BEFORE USING YOUR  
CARPET WAShER.  
Always connect to a properly Earthed  
outlet. Unplug from outlet when not in  
use and before conducting  
maintenance or troubleshooting.  
WARNING:  
Use indoors only  
To reduce the  
risk of fire, electric shock, or injury:  
Keep openings free of dust, lint, hair, etc.  
Keep appliance on a level surface  
Turn off all controls before unplugging  
Be extra careful when cleaning stairs  
Pay close attention when working  
around children  
Do not immerse; use only on surfaces moistened  
by cleaning process  
Do not leave machine when it is plugged in  
Do not service machine when it is plugged in  
If the supply cord is damaged, it must be replaced  
by the manufacturer or its service agent in order  
to avoid a hazard  
SAvE ThESE  
Do not use machine if it has been dropped,  
damaged, left outdoors or dropped into water  
INSTRUCTIONS.  
Do not pull or carry by cord, use cord as a  
handle, close door on cord, pull cord around sharp  
corners or edges, run appliance over cord, or  
expose cord to heated surfaces  
ThIS moDEL IS foR hoUSEhoLD USE oNLY.  
WARNING:  
This appliance must  
Do not carry the appliance while in use  
Do not unplug by pulling on cord; unplug by  
grasping plug not the cord  
be Earthed  
.
Do not handle plug or appliance with wet hands  
Do not put any object into appliance openings, use  
with blocked opening or restrict air flow  
Do not expose hair, loose clothing, fingers or body  
parts to openings or moving parts  
Do not pick up hot or burning objects  
Do not pick up flammable or combustible  
materials (lighter fluid, petrol, kerosene, etc.) or use  
in the presence of explosive liquids or vapours  
Do not use appliance in an enclosed space filled with  
vapours given off by oil base paint, paint  
thinner, some moth proofing substances,  
flammable dust, or other explosive or toxic vapours  
Remove plug from electrical outlet before cleaning  
or maintaining the appliance  
IMPORTANT  
foR oPERATIoN oN  
A 220-240 VoLT A.C. 50/60 hz PoWER  
SUPPLY oNLY.  
If your appliance is fitted with a nonrewireable  
BS 1363 plug it must not be used unless a 13  
amp (ASTA approved to BS 1362) fuse is fitted in  
the carrier contained in the plug. Spares may be  
obtained from your BISSELL supplier. If for any  
reason the plug is cut off, it must be disposed  
of, as it is an electric shock hazard should it be  
inserted into a 13 amp socket.  
3
w w w . b i s s e l l . c o m  
 
Product view  
Spray Trigger  
Power Switch  
Quick Release™  
Cord Wrap  
Tough Stain Tool  
Hose Secure Latch  
Upper Hose Wrap  
Power Cord  
Handle Assembly  
Ready-to-Use Hose  
Easy Carry  
Handle  
Clean Water/  
Formula Tank  
Oxy Gen2™  
PowerTool  
Large,  
Easy-To-Maneuver  
Wheels  
Lower Body  
Assembly  
Handle Release  
ReadyTools™  
Dial  
Dirty Water  
Tank  
WARNING:  
To reduce the risk of fire and electric  
shock due to internal component damage, use  
only BISSELL cleaning formulas intended for  
use with the carpet washer. Non-BISSELL  
cleaning solutions may harm the machine  
and void the warranty.  
PowerRoller  
Cleaning formula  
Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can wash and protect  
whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL  
cleaning solutions may harm the machine and will void the warranty.  
BISSELL  
BISSELL  
BISSELL  
BISSELL  
BISSELL  
BISSELL  
BISSELL  
Fiber Cleansing  
Formulawith  
Scotchgard™  
Protector  
Multi- Allergen  
Pet Odor and  
Natural Orange  
Extract Formula  
with Scotchgard™  
Protector  
Tough Stain  
Lavender Essence Oxy Gen2  
Formula with  
RemovalFormula Soil Removal™  
with ScotchgardFormula with  
Pre-cleaner™  
Scotchgard™  
Protector  
Scotchgard™  
Protector  
Protector  
4
w w w . b i s s e l l . c o m  
 
how to use this guide  
WARNING:  
Do not plug in your carpet  
washer until you have  
completely assembled it  
per the following instructions  
and are familiar with all  
instructions and operating  
procedures.  
This user’s guide has been designed to help  
you get the maximum satisfaction from your  
ReadyDry carpet washer. You’ll find assembly  
and operating instructions, safety precautions,  
as well as maintenance and troubleshooting  
instructions. Please read this user’s guide  
thoroughly before assembling your carpet  
washer.  
Your carpet washer comes in three easy to  
assemble components:  
Tip: Regular carpet cleaning  
can reduce dust and allergens in  
your home.  
• Handle assembly  
• Upper hose wrap  
• Lower body assembly  
Four Phillips head screws are included and can  
be found taped to the handle assembly.  
1.  
Assembly  
The only tool you will need to assemble your  
ReadyDry is a Phillips head screwdriver.  
1. Slide upper handle into lower body assembly  
and secure with 2 screws.  
2a.  
2. Attach upper hose wrap using 2 screws.  
3. Wrap hose clockwise around the upper and  
lower hose wraps as shown on page 4. Be  
sure to properly secure grip into the notched  
holder.  
4. Keep hose locked in place with the  
secure latch.  
5. Wrap the power cord as shown on page 4.  
2b.  
Upper Hose  
Wrap Screws  
6. Place Oxy Gen2 PowerTool in the center tool  
caddy and the tough stain tool on the hose  
wand.  
Upper Handle  
Screws  
5
w w w . b i s s e l l . c o m  
 
Special features of your BISSELL ReadyDry  
Your BISSELL ReadyDry carpet washer is a  
home cleaning system that uses a combination  
of hand hot tap water, BISSELL advanced cleaning  
formula, the innovative PowerRoller and suction  
to safely wash carpet and area rugs.  
WARNING:  
Toreduce the riskoffire,use only  
BISSELL advanced deep cleaning  
formula for full size machines in your  
carpet washer. Use of cleaning  
PowerRoller  
formulas that contain lemon or  
pine oilmaydamage thisappliance  
andvoidthe warranty.Chemical  
spotcleanersorsolvent-basedsoil  
removersshouldnotbe used.These  
productsmayreactwiththe plastic  
materialsusedinyourcarpetwasher  
causing cracking or pitting.  
The PowerRoller is designed for great cleaning  
performance with fast drying results. It traps, lifts  
and removes dirt and debris. Unlike  
traditional carpet washers, where cleaning  
solution is sprayed directly into the carpet, the  
PowerRoller absorbs the majority of the spray  
from the machine, meaning your carpet and  
area rugs get cleaned and revitalized, while still  
allowing you to get back on them in less than 30  
minutes. When in the upright position for storage  
or tool use, the PowerRoller is lifted off the floor  
surface and held in place. This will also help the  
PowerRoller dry between uses. The PowerRoller  
can be washed or replaced as needed.  
ReadyTools™ Dial  
The ReadyTools feature allows you to choose  
between FLOOR CLEANING or cleaning with TOOLS  
simply by turning the dial. The TOOLS setting  
allows for above floor cleaning of upholstery,  
stairs, creases along baseboards and other hard  
to reach areas. Simply choose the tool that is  
appropriate for the job, attach it to the flexible  
hose and you are ready to go.  
Oxy Gen2 PowerTool  
The Oxy Gen2 PowerTool is an advanced stain  
fighting tool. By adding Oxy Gen2 multi-purpose  
formula to the tool, tough stains such as coffee,  
juice, cola and red wine are easier to clean up.  
The tool can store ready to use with the  
Oxy Gen2 formula in it.  
Easy carry handle  
Located in the back of the machine,the easy carry  
handle makes it easy to carry the machine.Refer to  
page 4 for location.  
6
w w w . b i s s e l l . c o m  
 
Operation  
Before you clean  
1. If desired, move furniture to another area if  
cleaning an entire room.  
2. vacuum area with a dry vacuum cleaner  
before cleaning.  
EXIT  
9
0
1
2
1
3. Plan your cleaning route to leave an exit  
path. It is best to begin cleaning the corner  
farthest from your exit.  
7
6
5
'
3
1
AR  
ST  
T
R
E
2
E
H
3
'
4
4
Fill the clean water/formula tank  
1. Remove the clean water/formula tank from the  
base of the machine by pulling up and out from  
the back. You can also detent the handle and  
pull the tank straight up if you desire.  
2. Unscrew the black cap and red insert. Remove  
and set aside.  
3. Fill the tank up to the FILL LINE with hand  
hot tap water.  
4. Add 3 ounces of formula (always use  
genuine BISSELL formulas to maximize  
cleaning and for the safety of your machine).  
5. Replace the cap and insert and tighten by  
turning clockwise.  
6. Replace the clean water/formula tank back  
into the machine. Be sure that the cap is  
seated in the receiver.  
Carpet washing  
1. Make sure the ReadyTools Dial is in the  
FLOOR CLEANING position.  
2. Plug the ReadyDry into the proper outlet and  
turn the power on using the switch in the  
back.  
3. With your foot, press the gray handle release  
lever located on the back of the unit. Take  
care to notice the way the machine floats  
forward.  
4. While pressing the spray trigger make one  
forward wet pass and another one back.  
Repeat once and move on to the next  
section of carpet or area rug to be washed.  
Take care not to run over loose objects of  
the edges of area rugs.  
Tip:  
Thorough vacuuming  
before carpet washing will prevent  
early clogging of the lint screen.  
7
w w w . b i s s e l l . c o m  
 
Operation  
Empty the dirty water tank  
1. When the dirty water tank level reaches the FULL line,  
when the float trips or when finished carpet washing,  
turn power switch off.  
WARNING:  
To reduce the risk of fire  
and electric shock due to  
internal component  
2. Remove dirty water tank by lifting straight up.  
Carry it to the sink or wherever you plan to  
dump the dirty water.  
damage, use only BISSELL  
cleaning fluids intended for  
use with the carpet washer.  
Non-BISSELL cleaning  
solutions may harm the  
machine and void  
3. Remove the tethered cap on the rear of  
the tank.  
4. Pour out the dirty water, rinse tank and replace  
the warranty.  
the cap.  
5. To continue carpet washing refer back to page  
7 and begin with "Fill the clean water/formula  
tank."  
If carpet washing is complete, refer to the  
“Maintenance and care” section on page 11.  
Pretreating (optional)  
1. Pretreating (optional)  
Pretreating is recommended to improve cleaning  
effectiveness for heavily soiled carpet in high traffic  
areas such as entry ways and hallways. Please keep  
in mind that pretreating will wet the carpet and could  
impact dry time.  
To pretreat:  
A. Using the BISSELL Tough Stain  
Pre-cleaner, generously spray evenly over  
soiled area, do not overwet.  
B. Wait 3-5 minutes before carpet washing.  
C. Clean as normal using your BISSELL ReadyDry,  
following the instructions on page 7.  
ReadyTools (cleaning with attachments)  
Your ReadyDry carpet washer comes equipped  
with a hose and at least two attachments for  
cleaning stairs, upholstery, stains and more.  
Important! If using the machine to clean  
upholstery, check upholstery tags.  
1. Check manufacturer’s tag before cleaning. “W”  
or “WS” on the tag means you can use your  
ReadyDry. If the tag is coded with “X” or “S”  
(with a diagonal strike through), or says “Dry  
Clean Only,” do not proceed. Do not use on  
velvet or silk. If manufacturer’s tag is missing  
or not coded, check with your furniture dealer.  
Manufacturer’s tag  
w w w . b i s s e l l . c o m  
8
 
Operation  
ReadyTools™ (continued)  
2. Check for colorfastness in an inconspicuous  
place.  
3. If possible, check upholstery stuffing.  
Colored stuffing may bleed through fabric  
when wet.  
4. Plan activities to give upholstery time to dry.  
5. Vacuum thoroughly to pick up loose debris and  
pet hair. Use a vacuum with a brush attachment  
and a crevice tool to clean in fabric folds and tufts.  
6. To start cleaning with attachments, follow  
the instructions on page 7, beginning with  
"Fill the clean water/formula tank".  
7. Set the ReadyTools dial to the TOOLS setting.  
This will allow for suction from the hose.  
8. Attach the desired cleaning tool to the end of  
the hose.  
9. Clean by pressing the spray trigger to spray  
cleaning solution onto the area to be  
cleaned. Slowly move the tool back and forth  
over the soiled surface. Release the spray  
trigger to suction dirty water. Continue to  
clean in the area, working in small sections,  
until dirt is removed.  
Caution: Do Not Overwet.  
10. When finished cleaning, remove and rinse  
the tool(s) in clean, running water.  
11. It is recommended that you suction clean  
water from the tap to rinse out the hose.  
12. Before wrapping hose onto tool rack, lift end  
of hose and stretch out to ensure all water is  
cleared from hose.  
13. Wrap hose around tool rack.  
14. Empty dirty water tank and rinse out,  
following instructions on page 8.  
15. If the ReadyTools dial becomes difficult to  
turn, the diverter assembly that holds the dial  
may need to be cleaned. To clean, flush hot  
water through the nozzle. Make sure the dial  
is set to FLOOR CLEANING.  
9
w w w . b i s s e l l . c o m  
 
Operation  
Oxy Gen2™ PowerTool  
To use the Oxy Gen2 PowerTool:  
1. Pull out the rubber stopper in the tank.  
2. Fill with Oxy Gen2formula.  
3. Replace the rubber stopper and attach the  
Rubber Stopper  
tool to the hose grip.  
4. Refer to page 9 “ReadyTools” steps 9-10.  
Maintenance and care  
Machine care  
For best results, a few simple steps can assure  
your carpet washer is well maintained after your  
cleaning is complete.  
Lint Screen  
1. Turn power switch off. Unplug the machine  
and wrap the power cord.  
2. After emptying the dirty water tank, rinse it  
with running hand hot tap water, taking care  
to clean all around the interior.  
3. If necessary, check and clean out the lint screen  
after each use by wiping clean any visible residue.  
4. Replace the dirty water tank back into the machine.  
5. Any loose hair or debris can be pulled from  
the PowerRoller and thrown away.  
6. To clean the attachments, remove from hose  
and rinse in clean, running water. Dry before  
storing. Clean the hose by suctioning clean  
water from the tap. Before wrapping back on  
machine, lift end of hose and stretch out to  
ensure all water is cleared from hose.  
7. Wipe the machine’s exterior with a soft cloth.  
8. Machine Storage: Allow PowerRoller to dry  
completely before storing. Put the unit away  
in a closet or basement for the next use.  
Store in a protected, dry area. Since this  
product uses water, it must not be stored  
where there is a danger of freezing. Freezing  
will damage internal components and void  
the warranty.  
w w w . b i s s e l l . c o m  
10  
 
Maintenance and care  
Cleaning/replacing the PowerRoller  
1. Turn power switch to off and unplug the  
machine.  
3.  
2. Remove both tanks, detent the handle and  
turn the machine on its back.  
3. Remove the 6 screws from the sole plate  
using a Phillips head screwdriver.  
4. Turn the machine on its side so the cord side  
is facing up.  
5. Remove the the swing arm (with dowel) and  
roller assembly.  
5.  
6. Slide the PowerRoller up off the dowel and  
replace as desired.  
7. To replace, slide the PowerRoller onto the  
metal dowel and place the end with the  
taller cog down into the lower swing arm.  
Ensure the dowel is seated and that the  
belt is around the roller cog. Place the other  
swing arm in position and push the roller  
down into the front cavity.  
6.  
8. Re-attach the sole plate using the 6 screws.  
Over-current PowerRoller motor protection  
An internal over-current protector has been  
designed into your carpet washer to protect the  
PowerRoller motor from over-current. When the  
over-current protector activates, the PowerRoller  
motor will stop operating. If this happens,  
proceed as follows:  
7a.  
7b.  
1. Turn the power switch off and unplug from  
the electrical outlet.  
2. Allow the carpet washer to sit for 15 seconds.  
The over-current protector automatically  
resets and cleaning may continue. If the  
PowerRoller still does not work or the over-  
current protector continues to activate, your  
carpet washer may need servicing.  
7c.  
Note: The over-current protector protects the  
PowerRoller motor only, not the main motor.  
If the over-current protector activates, the  
carpet washer will still operate; however, the  
PowerRoller and spray will not work.  
11  
w w w . b i s s e l l . c o m  
 
WARNING:  
To reduce the risk of fire, electric  
shock or injury, unplug from the  
outlet before servicing.  
Troubleshooting  
Reduced Spray OR No Spray  
Possible cause  
Remedies  
1. Clean water/formula tank may be empty  
1. Turn power switch off; refill tank with  
clean hand hot tap water and formula  
2. Clean water/formula tank may not be seated properly 2. Turn power switch off; remove tank  
and reseat  
3. Pump may have lost prime  
3. Turn power switch off; after 1 minute  
turn on and depress spray trigger  
Be sure there is cleaning formula in the  
clean water/formula tank, it will make the  
machine prime faster  
4. Spray tip may be clogged  
4. Remove spray tip and rinse thoroughly  
under hot water. Replace with the o-ring tip  
going down into the machine  
No spray through the hose  
Possible cause  
1. Pump may not be primed  
Remedies  
1. Turn ReadyTools dial to FLOOR CLEANING  
and depress spray trigger for a few a  
seconds until you see suction coming up  
the nozzle  
Turn ReadyTools dial back to TOOLS  
PowerRoller Does Not Turn  
Possible cause  
1. The brush belt is off or broken  
Remedies  
1. Refer to page 11, steps 1-5 for instructions  
on how to access the belt  
2. Look at the belt and check for breakage or  
mis-alignment on the cogs. If there is no  
evidence, replace all parts following steps 8-10.  
3. In the event your belt is broken, a replacement  
calling BISSELL consumer services. Refer  
tothepartslist onpage14.Completeinstallation  
instructions will come with the replacement belt  
Machine not picking up solution  
Possible cause  
1. Dirty water tank may not be seated properly  
Remedies  
1. Turn power switch off; reseat tank  
2. ReadyTools dial may be on TOOLS  
3. Float may have shut off  
2. Turn ReadyTools dial to FLOOR CLEANING  
3. Turn power switch off and empty tank if  
necessary. If tank is not full, wait  
30 seconds and turn power switch on  
4. Dirty water tank may be full  
4. Turn power switch off and empty tank  
Other maintenance or service not included in the manual should be performed by an  
authorized service representative.  
Thank you for selecting a BISSELL product.  
Please do not return this product to the store  
w w w . b i s s e l l . c o m  
12  
 
BISSELL Consumer Services  
If your BISSELL product should require service:  
In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you  
the location of a BISSELL Authorized Service Center in your area. for all other countries, contact your local in  
country distributor for questions, service, or repair.  
If you have questions about your warranty or need replacement parts please contact the numbers below.  
For UK inquiries:  
For Australian inquiries:  
monday - Thursday  
friday  
9 am — 5 pm  
9 am — 4 pm  
monday - friday 9 am — 5 pm  
BISSELL AUSTRALIA PTY LIMITED  
Unit 35  
15 Ricketts Road  
mount Waverley, Victoria 3149  
Australia  
BISSELL homecare (Overseas) Inc.  
The Boat Yard  
105 Straight Road  
old Windsor  
Berkshire, SL4 2SE  
United Kingdom  
Telephone: 1-800-811-183  
Telephone: 0870-225-0109  
For all other inquiries:  
For New Zealand inquiries:  
monday - friday 8 am — 4 pm  
monday - friday 9 am — 5 pm  
BISSELL homecare, Inc.  
Po Box 1888  
Parex Industries Ltd.  
5 Tolich Place  
Grand Rapids, mI 49501 USA  
Telephone: 01-616-453-4451  
fax: 01-616-453-1383  
henderson 0610  
Auckland  
New Zealand  
Telephone: 0800-247-735  
Or visit the BISSELL website - www.bissell.com  
When contacting BISSELL, have model number of unit available.  
Please record your model Number: ___________________  
Please record your Purchase Date: ___________________  
Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a  
warranty claim. See Warranty on page 16 for details.  
Please do not return this product to the store.  
13  
w w w . b i s s e l l . c o m  
 
Replacement parts  
Item Part No. Part Name  
1
2
3
4
5
6
7
8
203-7204 Dirty Water Tank Assembly  
203-7206 Dirty Water Tank Cap w/ Tether  
203-7207 Clean Water/formula Tank Assembly  
203-7211 Spray Tip  
203-7210 Spray Tip Cover  
203-7223 PowerRoller Assembly  
203-7226 Replacement Brush Belt (with instructions)  
203-7241 oxy Gen2 PowerTool Cap  
1
5
2
6
3
7
4
8
Formulas  
Item Part No. Part Name  
1
2
3
4
5
6
7
710 Series BISSELL fiber Cleansing formulawith ScotchgardProtector  
720 Series BISSELL multi-Allergen Removalformula with ScotchgardProtector  
730 Series BISSELL Pet odor and Soil Removalformula with ScotchgardProtector  
740 Series BISSELL Natural orange Extract formula with ScotchgardProtector  
750 Series BISSELL Lavender Essence formula with ScotchgardProtector  
810 Series BISSELL oxy Gen2™  
400 Series BISSELL Tough Stain Pre-cleaner™  
1
2
3
4
5
6
7
w w w . b i s s e l l . c o m  
 
14  
Additional accessories  
These items are available for purchase as accessories for your BISSELL ReadyDry:  
Item  
1
Part No.  
203-7240  
Part Name  
oxy Gen2PowerTool  
2
3
4
5
6
7
8
203-7238  
203-6653  
203-6654  
203-6652  
203-7240  
203-7239  
210-3040  
3" Tough Stain Tool  
4" Upholstery Tool  
6" Stair Tool  
Powered TurboBrushhand Tool  
Spraying 2-in-1 Crevice Tool  
Spraying Crevice Tool  
mesh Tool Storage Bag (Bag only)  
1
5
2
3
4
8
6
7
Cleaning Formula: Refer to bottom of page 4 of this guide for a full selection of cleaning  
formulas available for purchase.  
15  
w w w . b i s s e l l . c o m  
 
Warranty - BISSELL ReadyDry  
This warranty gives you specific legal rights, and you may also have other rights which may vary from country  
to country. If you need additional instruction regarding this warranty or have questions regarding what it may  
cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or  
contact your local in country distributor.  
Limited Two Year Warranty  
Subject to the *EXCEPTIoNS AND EXCLUSIoNS identified below, BISSELL homecare, Inc., will replace (with  
new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the  
original purchaser, for two years any defective or malfunctioning part do to manufacturers defect.  
This warranty applies to product used for personal, and not commercial or rental service. This warranty does  
not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction  
caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.  
For UK inquiries:  
For Australian inquiries:  
monday - Thursday  
friday  
9 am — 5 pm  
9 am — 4 pm  
monday - friday 9 am — 5 pm  
BISSELL AUSTRALIA PTY LIMITED  
Unit 35  
15 Ricketts Road  
mount Waverley, Victoria 3149  
Australia  
BISSELL homecare (Overseas) Inc.  
The Boat Yard  
105 Straight Road  
old Windsor  
Berkshire, SL4 2SE  
United Kingdom  
Telephone: 1-800-811-183  
Telephone: 0870-225-0109  
For all other inquiries:  
For New Zealand inquiries:  
monday - friday 8 am — 4 pm  
monday - friday 9 am — 5 pm  
BISSELL homecare, Inc.  
Po Box 1888  
Parex Industries Ltd.  
5 Tolich Place  
Grand Rapids, mI 49501 USA  
Telephone: 01-616-453-4451  
fax: 01-616-453-1383  
henderson 0610  
Auckland  
New Zealand  
Telephone: 0800-247-735  
BISSELL hOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL  
DAMAGES OF ANY NATURE ASSOCIATED WITh ThE USE OF ThIS PRODUCT.  
BISSELLS LIABILITY WILL NOT EXCEED ThE PURChASE PRICE OF ThE PRODUCT.  
*EXCEPTIONS AND EXCLUSIONS FROM ThE TERMS OF ThE LIMITED WARRANTY  
ThIS WARRANTY IS EXCLUSIvE AND IN LIEU OF ANY OThER WARRANTIES  
EIThER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WhICh MAY ARISE  
BY OPERATION OF LAW, INCLUDING ThE IMPLIED WARRANTIES OF  
MERChANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED  
©2009 BISSELL homecare, Inc  
TO ThE TWO YEAR DURATION FROM ThE DATE OF PURChASE AS  
DESCRIBED ABOvE.  
Grand Rapids, michigan  
All rights reserved. Printed in USA  
Part Number 120-4095  
Rev 1/09  
Scotchgard is a trademark of 3m  
w w w . b i s s e l l . c o m  
16  
 

Belkin Switch F5D4071 User Manual
Bowflex Home Gym BDS 220 User Manual
Briggs Stratton Lawn Mower 1695353 User Manual
Broan Patio Furniture 942224 User Manual
Bushnell Hunting Equipment 205107 User Manual
Cannondale Motorcycle C440 User Manual
Canon All in One Printer MultiPASSTM C50 User Manual
Canon Photo Printer ES20 User Manual
Canon Printer 2163B002 User Manual
Chevrolet Automobile 2009 Silverado User Manual