Cisco Systems Network Card 15454 ML 4FC= User Manual

Installing Cisco ONS 15454 SONET/SDH  
FC_MR-4 Cards  
Product Name: 15454-ML-4FC=  
This document lists regulatory requirements and describes installation procedures for the Cisco ONS  
15454/ONS 15454 SDH FC_MR-4 card. It also contains removal instructions and technical  
specifications. Use this document in conjunction with the Cisco ONS 15454 SDH Reference Manual, the  
Cisco ONS 15454 SDH Procedure Guide, the Cisco ONS 15454 Reference Manual, and the Cisco ONS  
15454 Procedure Guide.  
This document contains the following sections:  
“OC192 LR/STM64 LH ITU 15xx.xx Card-Level Indicators” section on page 5  
“OC192 LR/STM64 LH ITU 15xx.xx Port-Level Indicators” section on page 5  
“Obtaining Documentation” section on page 10  
“Obtaining Technical Assistance” section on page 12  
This document contains the following procedures:  
Procedure: Verify Successful Turn Up of the OC192 LR/STM64 LH ITU 15xx.xx Card, page 9  
FC_MR-4 Card Description  
Warning  
Class 1 (21 CFR 1040.10, 1040.11, and IEC 60825-1 2001-01) laser products. Invisible laser radiation may  
be emitted from the end of the unterminated fiber cable or connector. Do not stare into the beam or  
view directly with optical instruments. Viewing the laser output with certain optical instruments (for  
Co rp o ra t e He a d q u a rt e rs :  
Cis c o S ys t e m s , In c ., 1 7 0 We s t Ta s m a n Drive , S a n J o s e , CA 9 5 1 3 4 -1 7 0 6 US A  
Copyright © 2003 Cisco System s, Inc. All rights reserved.  
 
 
FC_MR-4 Card Description  
FC_MR-4 Card-Level Indicators  
Table 0-1 describes the two card-level LEDs on the FC_MR-4 card.  
Table 0-1 FC_MR-4 Card-Level Indicators  
Card-Level Indicators Description  
Red FAIL LED  
The red FAIL LED indicates that the card’s processor is not ready. Replace the  
card if the red FAIL LED persists.  
Green ACT LED  
If the ACTV/STBY LED is green, the card is operational and ready to carry  
traffic.  
FC_MR-4 Port-Level Indicators  
Each FC_MR-4 port has a corresponding ACT/LNK LED. The ACT/LNK LED is solid green if the port  
is available to carry traffic, is provisioned as in-service, and in the active mode. The ACT/LNK LED is  
flashing green if the port is carrying traffic. The ACT/LNK LED is steady amber if the port is not enabled  
and the link is connected, or if the port is enabled and the link is connected but there is a SONET  
transport error. The ACT/LNK LED is unlit if there is no link.  
You can find the status of the card ports using the LCD screen on the ONS 15454 fan-tray assembly. Use  
the LCD to view the status of any port or card slot; the screen displays the number and severity of alarms  
for a given port or slot. Refer to the Cisco ONS 15454 Troubleshooting Guide for a complete description  
of the alarm messages.  
FC_MR-4 Card Specifications  
The FC_MR-4 card has the following specifications:  
Environmental  
Operating temperature  
C-Temp (15454-E100T): –5 to +55 degrees Celsius (23 to 131 degrees Fahrenheit)  
Operating humidity: 5 to 95%, noncondensing  
Power consumption: 60 W, 1.35 A, 221.93 BTU/hr  
Dimensions  
Height: 321.3 mm (12.650 in.)  
Width: 18.2 mm (0.716 in.)  
Depth: 228.6 mm (9.000 in.)  
Card weight: 1.17 kg (2.59 lb)  
Compliance  
For compliance information, refer to the Cisco Optical Transport Products Safety and  
Compliance Information.  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
3
 
   
Installation Procedures  
Installation Procedures  
Use this section if you are installing the FC_MR-4 card for the first time. After you become familiar with  
ONS 15454 SONET/SDH card installation and boot up, use this section as a reference. For information  
about fiber optic cable installation, see the Cisco ONS 15454 SDH Reference Manual, the Cisco ONS  
15454 SDH Procedure Guide, the Cisco ONS 15454 Reference Manual, or the Cisco ONS 15454  
Procedure Guide.  
Warning  
Caution  
Hazardous voltage or energy may be present on the backplane when the system is operating. Use  
caution when servicing.  
Always use the supplied electrostatic discharge (ESD) wristband when working with an ONS 15454  
SONET/SDH. Plug the wristband cable into the ESD jack located on the lower right outside edge of the  
shelf assembly and ensure the shelf assembly is properly grounded.  
FC_MR-4 cards have electrical plugs that plug into electrical connectors on the shelf assembly  
backplane. When the ejectors are fully closed, the card plugs into the shelf assembly backplane. Figure 2  
shows general card installation. The example shows the installation in an ONS 15454. The procedure in  
an ONS 15454 SDH is identical.  
Figure 2  
Installing a card in an ONS 15454  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
4
 
   
Related Documentation  
Procedure: Install the FC_MR-4 Card  
Step 1  
Step 2  
Step 3  
Open the card ejectors.  
Slide the card along the guide rails into the correct slot.  
Close the ejectors.  
Procedure: Verify Turn Up of the FC_MR-4 Card  
Follow the steps in this section to verify card turn up. If one or more of the Cisco Transport Controller  
(CTC) software screen conditions according to this procedure are not met, reinstall the card. Replace the  
unit if the faulty state persists.  
Step 1  
Step 2  
Verify that power is applied to the shelf assembly.  
Verify the LED activity:  
The red FAIL LED turns on for 20 to 30 seconds. The ACT LED is amber for 3 to 5 seconds.  
The red FAIL LED blinks for up to 2 minutes.  
The FAIL and ACT LEDs blink once and turn off for 1 to 5 seconds.  
The ACT LED turns on.  
Note  
If the red FAIL LED does not turn on, check the power.  
Note  
If you insert a card into a slot provisioned for a different card, all LEDs turn off.  
Step 3  
Step 4  
Verify that the ACT or ACT/STBY LED is on. The signal fail (SF) LED can persist until all card ports  
connect to their far end counterparts and a signal is present.  
When you have displayed Cisco Transport Controller (CTC) on your workstation, verify that the card  
appears in the correct slot on the CTC node view. See the Cisco ONS 15454 SDH Reference Manual, the  
Cisco ONS 15454 SDH Procedure Guide, the Cisco ONS 15454 Reference Manual, or the Cisco ONS  
15454 Procedure Guide.  
Related Documentation  
DOC-7815934= Cisco ONS 15454 Procedure Guide  
DOC-7815981= Cisco ONS 15454 Reference Manual  
DOC-7815982= Cisco ONS 15454 Troubleshooting Guide  
DOC-7815983= Cisco ONS 15454 SDH Procedure Guide  
DOC-7815988= Cisco ONS 15454 SDH Reference Manual  
DOC-7815989= Cisco ONS 15454 SDH Troubleshooting Guide  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
5
 
   
Obtaining Documentation  
Obtaining Documentation  
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several  
ways to obtain technical assistance and other technical resources. These sections explain how to obtain  
technical information from Cisco Systems.  
Cisco.com  
You can access the most current Cisco documentation on the World Wide Web at this URL:  
You can access the Cisco website at this URL:  
International Cisco websites can be accessed from this URL:  
Ordering Documentation  
You can find instructions for ordering documentation at this URL:  
You can order Cisco documentation in these ways:  
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from  
the Ordering tool:  
Nonregistered Cisco.com users can order documentation through a local account representative by  
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in  
North America, by calling 800 553-NETS (6387).  
Cisco Optical Networking Product Documentation CD-ROM  
Optical networking-related documentation, including Cisco ONS 15454 product documentation, is  
available in a CD-ROM package that ships with your product. The Optical Networking Product  
Documentation CD-ROM is updated periodically and may be more current than printed documentation.  
Documentation Feedback  
You can submit e-mail comments about technical documentation to [email protected].  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
6
 
Obtaining Technical Assistance  
You can submit comments by using the response card (if present) behind the front cover of your  
document or by writing to the following address:  
Cisco Systems  
Attn: Customer Document Ordering  
170 West Tasman Drive  
San Jose, CA 95134-9883  
We appreciate your comments.  
Obtaining Technical Assistance  
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco  
Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services,  
online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for  
technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.  
Cisco TAC Website  
The Cisco TAC website provides online documents and tools for troubleshooting and resolving technical  
issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365  
days a year. The Cisco TAC website is located at this URL:  
Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you  
have a valid service contract but do not have a login ID or password, register at this URL:  
Opening a TAC Case  
Using the online TAC Case Open Tool is the fastest way to open P3 and P4 cases. (P3 and P4 cases are  
those in which your network is minimally impaired or for which you require product information.) After  
you describe your situation, the TAC Case Open Tool automatically recommends resources for an  
immediate solution. If your issue is not resolved using the recommended resources, your case will be  
assigned to a Cisco TAC engineer. The online TAC Case Open Tool is located at this URL:  
For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely  
degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers  
are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.  
To open a case by telephone, use one of the following numbers:  
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)  
EMEA: +32 2 704 55 55  
USA: 1 800 553-2447  
For a complete listing of Cisco TAC contacts, go to this URL:  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
7
 
Obtaining Additional Publications and Information  
TAC Case Priority Definitions  
To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.  
Priority 1 (P1)—Your network is “down” or there is a critical impact to your business operations. You  
and Cisco will commit all necessary resources around the clock to resolve the situation.  
Priority 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your  
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco  
will commit full-time resources during normal business hours to resolve the situation.  
Priority 3 (P3)—Operational performance of your network is impaired, but most business operations  
remain functional. You and Cisco will commit resources during normal business hours to restore service  
to satisfactory levels.  
Priority 4 (P4)—You require information or assistance with Cisco product capabilities, installation, or  
configuration. There is little or no effect on your business operations.  
Obtaining Additional Publications and Information  
Information about Cisco products, technologies, and network solutions is available from various online  
and printed sources.  
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Go  
to this URL to visit the company store:  
The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as  
ordering and customer support services. Access the Cisco Product Catalog at this URL:  
Cisco Press publishes a wide range of general networking, training and certification titles. Both new  
and experienced users will benefit from these publications. For current Cisco Press titles and other  
information, go to Cisco Press online at this URL:  
Packet magazine is the Cisco quarterly publication that provides the latest networking trends,  
technology breakthroughs, and Cisco products and solutions to help industry professionals get the  
most from their networking investment. Included are networking deployment and troubleshooting  
tips, configuration examples, customer case studies, tutorials and training, certification information,  
and links to numerous in-depth online resources. You can access Packet magazine at this URL:  
iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet  
business strategies for executives. You can access iQ Magazine at this URL:  
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering  
professionals involved in designing, developing, and operating public and private internets and  
intranets. You can access the Internet Protocol Journal at this URL:  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
8
 
Obtaining Additional Publications and Information  
Training—Cisco offers world-class networking training. Current offerings in network training are  
listed at this URL:  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
9
 
Obtaining Additional Publications and Information  
Installing Cisco ONS 15454 SONET/SDH FC_MR-4 Cards  
78-16233-01  
1 0  
 

Belkin Power Supply F6U600AU User Manual
BenQ Projector MP723 User Manual
Black Decker Bicycle Accessories GN032 User Manual
Black Decker Iron F980 User Manual
Black Decker Rice Cooker HS90 User Manual
Carrier Air Conditioner T 298 User Manual
Casio Clock DQ 746 User Manual
Chamberlain Stud Sensor PIR2300R User Manual
Chromalox Electric Heater PG412 10 User Manual
Cisco Systems IP Phone 7690 User Manual