Cisco Systems IP Phone 6901 User Manual

A P P E N D I X  
E
Installing the Wall Mount for the Cisco Unified  
IP Phone 6901 and 6911  
This appendix contains information on installing the wall mount for use with the Cisco Unified IP Phone  
6901 and 6911 phones.  
Installing a Wall Mount for the Cisco Unified IP Phone 6901  
The following section describes how to install the Wall Mount plate for use with the  
Cisco Unified IP Phone 6901.  
Cisco recommends that you use the Leviton Wall Mount plate (Leviton type number: 4108W-0SP) for  
mounting the Cisco Unified IP Phone 6901. The wall mount plate must be ordered separately from the  
phone.  
Figure E-1 shows a list of items required to mount the Cisco Unified IP Phone 6901 on the wall using  
the Leviton Wall Mount plate.  
Figure E-1  
Leviton Wall Mount Plate  
4
A
B
6
8
7
1
2
1
RJ45 Connector  
2
Leviton Wall Mount Plate  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-1  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6901  
Installing the Phone on Wall Mount Plate  
To install the phone on the wall mount plate, follow these steps:  
Procedure  
Plug the telephone line cord (RJ45 connector) into the phone jack at the base of the phone (Figure E-3).  
Step 1  
Figure E-3  
RJ45 Connector in the Phone Jack  
2
1
1
2
Network Port on the Phone  
RJ45 Connector  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-3  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6901  
Step 2  
Plug the RJ45 connector into the wall mount phone jack (Figure E-4).  
Figure E-4  
RJ45 Connector in the Wall Mount Jack  
2
3
1
4
1
2
Network Port on the Phone  
RJ45 Connector  
3
4
Wall Mount Plate  
Network Port on the Wall Mount Plate  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-4  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6901  
Step 3  
Slip the mounting holes on the base of the wall mount plate and over the wall mount pins (Figure E-5).  
Figure E-5  
Mounting Holes  
1
2
1
2
Mounting Hole on the Phone  
Wall Mount Pin on the Wall Mount Plate  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-5  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6901  
Step 4  
Firmly slide the IP Phone down into place (Figure E-6).  
Figure E-6 Sliding the IP Phone  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-6  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
The following section describes how to install the wall mount for use with the Cisco Unified IP Phone  
6911.  
Figure E-7 shows a list of items included in the Wall Mount Kit for the Cisco Unified IP Phone 6911.  
Figure E-7  
Wall Mount Kit for Cisco Unified IP Phone 6911  
Screws  
(4)  
Anchors  
(4)  
Machine  
screws  
(2)  
Phone bracket  
Wall bracket  
Ethernet  
cable  
Lock-down  
key  
The package includes the following items:  
One phone bracket  
One wall bracket  
Four 10-12x1 inch Phillips-head screws with 4 anchors  
Two 4-40x1/4 inch machine screws  
One six-inch Ethernet cable  
One key if the bracket includes the optional lock  
Before You Begin  
You will need these tools to install the bracket:  
#1 and #2 Phillips-head screwdrivers  
Level  
You must also install an Ethernet jack for the telephone in the desired location if an Ethernet jack does  
not currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot use a  
regular telephone jack. For more information on phone installation requirements and warnings, see the  
Setting Up the Cisco Unified IP Phone chapter.  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-7  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Installing the Bracket  
To install the phone on the wall, follow these steps:  
Procedure  
Step 1  
Mount the wall bracket in the desired location (Figure E-8). You can install the wall bracket over an  
Ethernet jack, or you can run the Ethernet network cable to a jack nearby.  
a. Use the Level to ensure the wall bracket is level, then use a pencil to mark the screw holes.  
b. Using a #2 Phillips-head screwdriver, carefully center the anchor over the pencil mark and press the  
anchor into the wall to make markings on the wall.  
c. Screw the anchor clockwise into the wall until it is seated flush.  
d. Use the included screws and a #2 Phillips-head screwdriver to attach the wall bracket to the wall.  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-8  
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Figure E-8  
Mounting the Wall Bracket  
A
B
Mark mounting  
holes through  
bracket on wall  
Level wall  
bracket on wall  
C
D
Screw bracket  
to wall using  
Phillips head  
screws  
Insert anchors  
into wall  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-9  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Step 2  
Attach the phone bracket to the IP Phone (Figure E-9).  
a. Detach the handset cord (and headset cord, if there is a headset), power cord, and any other attached  
cords from the base of the phone.  
b. Remove the label covers that are concealing the screw holes.  
c. Attach the phone bracket by inserting the tabs into the mounting tabs on the phone. The phone’s  
ports should be accessible through the holes in the bracket.  
d. Secure the phone bracket to the IP Phone with the Phillips-head screws.  
e. Thread the handset cord (and headset cord, if using one). Reattach the cords and seat them in the  
clips incorporated into the phone body.  
Figure E-9  
Attaching the Phone Bracket  
Screw holes  
Slot for  
mounting tabs  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-10  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Step 3  
Remove the handset wall hookswitch in the handset rest, rotate the hookswitch by 180 degrees, and  
reinsert the hookswitch. The hookswitch should have a lip on which the handset catches when the phone  
is vertical (Figure E-10).  
Figure E-10  
Preparing the Handset Hookswitch  
1
2
3
4
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-11  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Step 4  
Attach the Ethernet cable to the 10/100 SW network port and wall jack.  
If you are connecting a network device (such as a computer) to the phone, attach the cable to the  
10/100 PC access port.  
If you are using an external power supply, plug the power cord into the phone and dress the cord by  
clipping it into the clips incorporated into the phone body next to the 10/100 PC port (Figure E-11).  
Figure E-11  
Attaching the Cables  
Wall bracket  
Phone bracket  
Network  
port  
Handset port  
AC adapter  
port  
Phone bracket  
cable access hole  
U-shaped holes  
for cables  
(optional power  
cable)  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-12  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Step 5  
Step 6  
Attach the phone to the wall bracket by inserting the tabs on the top of the phone bracket into the slots  
on the wall bracket. Ensure that the power cord and any other cable that does not terminate in the wall  
behind the bracket are positioned in one of the cable-access openings in the bottom of the bracket. The  
phone and wall brackets’ openings together form circular openings with room for one cable per opening  
Use the locking key to lock the phone to the wall bracket.  
Figure E-12  
Attaching the Phone to the Wall Bracket  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-13  
 
 
Appendix E Installing the Wall Mount for the Cisco Unified IP Phone 6901 and 6911  
Installing a Wall Mount for the Cisco Unified IP Phone 6911  
Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.6 (SCCP and SIP)  
OL-24582-01  
E-14  
 

Black Decker Planer 3375 User Manual
Black Decker Planer 7698K User Manual
Boppy Swing Sets 32810 User Manual
Bosch Appliances Dishwasher SHX99A15UC User Manual
Bose Speaker System 2II User Manual
Brady Printer 2461 User Manual
Bush Hog Tiller RTS40 04 User Manual
Cannon All in One Printer IR 2870 User Manual
Chauvet Landscape Lighting 18VW User Manual
Christie Digital Systems Projector 38 VIV204 01 User Manual